楼承板栓钉是楼承板作为组合连接的连接件。施工采用电弧式楼承板栓钉焊机和焊枪，采用脱氧电弧耐热陶瓷座圈。对于大面积，建议使用楼承板栓钉焊机。那么了解楼承板栓钉的作用和焊接方法是怎样的呢？

The floor support plate stud is the connector of the floor support plate as a combined connection. The construction adopts the arc floor support plate stud welding machine and welding gun, and adopts the deoxidized arc heat-resistant ceramic seat ring. For large areas, it is recommended to use floor bearing plate stud welding machine. So what is the function and welding method of floor support plate stud?

楼承板栓钉的作用

Function of floor bearing plate stud

楼面梁同钢筋混凝土楼承板起组合连接作用的连接件，施工采用拉弧型栓钉焊机和焊枪，并使用去氧弧耐热陶瓷座圈。因为栓钉穿透焊、焊接受到良多因素影响，包括楼承板镀锌层、板厚、与钢梁表面之间的间隙以及水、锈、渣、油漆等。

For the connecting pieces of the floor beam and the reinforced concrete floor bearing plate, the arc stud welding machine and welding gun are used in the construction, and the deoxidized arc heat-resistant ceramic seat ring is used. Because the stud penetration welding and welding are affected by many factors, including the galvanized layer of the floor support plate, the thickness of the plate, the gap with the surface of the steel beam, as well as water, rust, slag, paint, etc.

而且在施工现场，各种因素互相交织又不确定，因此，要获得良好的焊接质量，对焊接的工艺及施工要求很高，并在实际施工现场收集了海内外数种栓钉焊机的上万个焊接参数，通过波型分析和实际焊接质量的对比分析。

Moreover, in the construction site, various factors are intertwined and uncertain. Therefore, in order to obtain good welding quality, the requirements for welding process and construction are very high. Tens of thousands of welding parameters of several kinds of stud welding machines at home and abroad are collected at the actual construction site. Through wave pattern analysis and comparative analysis of actual welding quality.

底板栓钉焊接方法

Welding method of bottom plate stud

打开焊机焊枪电源，将柱形底板栓钉套在焊枪上，防止电弧座，启动焊枪，电流将被熔断，座圈会产生弧光，短时间后将柱形楼板的栓钉高速压在基材端部熔化，并切断电源。柱形楼板的栓钉焊接固定在母材上。

Turn on the power supply of the welding gun of the welding machine, put the stud of the cylindrical bottom plate on the welding gun to prevent the arc seat. When starting the welding gun, the current will be fused, and the seat ring will produce arc light. After a short time, press the stud of the cylindrical floor at high speed at the end of the substrate to melt, and cut off the power supply. The stud of the column floor is welded and fixed on the base metal.

济南楼承板栓钉焊接检验：柱楼承板钉质量以锤击为主，外观检验为辅，折弯检验取日产量的1/500。焊缝处无断裂视为合格，若焊缝有裂纹，则判断楼承板的栓钉报废，需在附近重新补焊一个柱栓钉作为补充。

Jinan floor support plate stud welding inspection: the quality of column floor support plate studs is mainly hammered, supplemented by appearance inspection, and the bending inspection is 1/500 of the daily output. It is deemed as qualified if there is no fracture at the weld. If there is crack in the weld, it is judged that the stud of the floor support plate is scrapped, and a column stud needs to be repaired nearby as a supplement.

楼承板钉的作用：楼承板钉用作楼承板组合梁的剪力连接件。它们主要依靠栓钉的抗剪力来承受剪力，并利用圆头来抵抗提升力。施工非常方便，下端有助焊剂，外覆陶瓷环。按设计位置用专用点焊机进行接触焊接，效率高。

Function of floor bearing plate nails: floor bearing plate nails are used as shear connectors of floor bearing plate composite beams. They mainly rely on the shear resistance of the stud to bear the shear force, and use the round head to resist the lifting force. The construction is very convenient, with flux at the lower end and ceramic ring covering. The contact welding is carried out with a special spot welder according to the design position, with high efficiency.

了解楼承板栓钉的作用和焊接方法的相关内容便是以上了，如果您对此有什么不了解的问题，欢迎来我们网站http://jyjfsj.com关注咨询！

That's all for understanding the function and welding method of floor support plate studs. If you have any questions about this, please come to our website http://jyjfsj.com Pay attention to consultation!