怎样防止楼承板表面与地面或空中的潮气接触呢？这个问题如果不好好解决的话，就会出现与您的施工期间之内，可能会造成楼承板工程质量的不好，下面就来看看吧。

How to prevent the surface of floor bearing plate from contacting with the moisture on the ground or in the air? If this problem is not properly solved, it will occur during your construction period, which may cause poor quality of the floor support plate project. Let's take a look at it below.

济南楼承板在安装时可利用位于屋面板下方用于隔热的反射箔，也可以简单的用作防潮，只需在其搭接处用防潮粘带密封即可。搭接的距离应大于100mm，定位箔片层时，保持紧密接触，使防潮胶带充分的发挥作用。箔片层必须覆盖在屋顶的支撑之间。

Jinan floor support plate can be installed by using the reflective foil under the roof panel for heat insulation, or simply used as moisture-proof. It only needs to be sealed with moisture-proof adhesive tape at its lap. The overlapping distance shall be greater than 100mm. When positioning the foil layer, keep close contact to make the moisture-proof tape fully play its role. The foil layer must cover between the supports of the roof.

如果发生此情况，冷凝就会在箔片的下方形成了。而为了减少楼承板在存放时下面的湿气凝聚，也必须在楼承板成型设备的下方与楼承板下方设置防潮板，以防止钢板下表面与地面或空中的潮气接触。

If this happens, condensation will form under the foil. In order to reduce the condensation of moisture under the floor support plate during storage, moisture-proof plates must also be set under the floor support plate forming equipment and under the floor support plate to prevent the lower surface of the steel plate from contacting with the moisture on the ground or in the air.

楼承板的表面层钢板比所接触的空气冷，或者空气中所带来的水汽凝聚在钢板上表面的时候，楼承板的下面就产生了一些冷凝。这种正常性的现象是必然不可预料，许多建筑物都面临着此类问题。

The steel plate on the surface layer of the floor support plate is colder than the contact air, or when the water vapor brought by the air condenses on the upper surface of the steel plate, some condensation occurs under the floor support plate. This normal phenomenon is inevitable and unpredictable, and many buildings are facing such problems.

比如在凉爽晴朗的夜晚，钢板将向空气中辐射的热量，直至钢板的温度降至周围空气的温度；有时气温只有5℃。但钢板甚至可以继续辐射，并保持比和它接触的空气冷，直到周围的空气温度升高。

For example, on a cool and sunny night, the steel plate will radiate heat into the air until the temperature of the steel plate drops to the temperature of the surrounding air; Sometimes the temperature is only 5 ℃. But the steel plate can even continue to radiate and remain colder than the air in contact with it until the ambient air temperature rises.

此外要知道楼承板凹凸不平的作用是增大摩擦系数。楼承板(钢承板，建筑压型钢板)是采用镀锌钢板经辊压冷弯成型，其截面成V型、U型、梯形或类似这几种形状的波形，主要用作永久性模板，也可被选为其他用途。更多相关事项就来我们网站http://jyjfsj.com咨询看看吧。

In addition, it is necessary to know that the function of uneven floor bearing plate is to increase the friction coefficient. Floor bearing plate (steel bearing plate, building profiled steel plate) is formed by rolling and cold bending of galvanized steel plate. Its cross section is V-shaped, U-shaped, trapezoidal or similar waveforms. It is mainly used as permanent formwork and can also be selected for other purposes. For more information, please visit our website http://jyjfsj.com Let's consult.