实际上岩棉板的校对方法需要几个步骤，其中一些步骤在后面的操作过程中比较复，下面就来了解了解吧。

In fact, the proofreading method of rock wool board requires several steps, some of which are more complex in the later operation process. Let's understand it below.

控制首层柱顶板和其他截面柱两端的标高有两种方式：根据相对标高或设计标高装置，常用的是相对标高装置。板柱吊装到位后，用大六角高强螺栓连接固定，

There are two ways to control the elevation of the top plate of the first floor column and the two ends of other section columns: according to the relative elevation or design elevation device, the common is the relative elevation device. After the plate column is hoisted in place, it is connected and fixed with large hexagon high-strength bolts,

测量上下柱顶面标高，用吊车吊起，用防滑杆调整接头间隙，驱动板楔，采用点焊抑制板柱下落，立柱安装好后，在立柱顶部放置水平仪，测量每个立柱顶的相对标高，并将结果与下一个立柱顶的预检长度进行比较，进行感应处理。

Measure the top elevation of the upper and lower columns, lift them with a crane, adjust the joint gap with an anti-skid rod, drive the plate wedge, and use spot welding to suppress the falling of the plate column. After the column is installed, place a level on the top of the column, measure the relative elevation of each column top, and compare the results with the pre inspection length of the next column top for induction treatment.

济南岩棉板认为当比对结果超过5mm时，应调整板柱楼承板。具体方法是在低碳板板上填充一定的厚度，但要注意每块板的厚度不能过大，以防增加其他节点的困难。

Jinan rock wool board believes that when the comparison result exceeds 5mm, the plate column floor bearing plate should be adjusted. The specific method is to fill a certain thickness on the low-carbon plate, but it should be noted that the thickness of each plate should not be too large to prevent the difficulty of adding other nodes.

上栏的垂直和水平十字准线。尽量使上下柱的交叉线重叠，以防止接头错开。如有误差，在连接耳板中填入厚度为0.5～1.0mm的垫板，并拧紧螺栓。

Vertical and horizontal crosshairs in the upper column. Try to overlap the cross lines of upper and lower columns to prevent staggered joints. If there is any error, fill the connecting padeye with a backing plate with a thickness of 0.5 ~ 1.0mm, and tighten the bolts.

对于板柱相关尺寸的预检，方法是下一个板柱的柱顶直线度误差是底轴线、位移、焊接变形、日照温度、直线度和以前板柱的其他错误。将直线度留在误差的相反方向。

For the pre inspection of relevant dimensions of slab column, the method is that the straightness error of the top of the next slab column is the bottom axis, displacement, welding deformation, sunshine temperature, straightness and other errors of the previous slab column. Leave the straightness in the opposite direction of the error.

在板柱、底板板楔或千斤顶的偏斜方向，在不超过单节柱直线度的前提下，小范围控制柱顶轴线偏移，并拧紧临时连接凸耳的大六角高强度螺栓。附加扭矩值。凸耳板上螺栓孔的直径应比螺栓的直径大4.0mm。在连接标准柱的相关梁装置上形成标准框架体。

In the deflection direction of plate column, bottom plate wedge or Jack, on the premise of not exceeding the straightness of single section column, the offset of column top axis shall be controlled in a small range, and the large hexagon high-strength bolts with temporary connecting lugs shall be tightened. Additional torque value. The diameter of the bolt hole on the lug plate shall be 4.0mm larger than the diameter of the bolt. The standard frame body is formed on the relevant beam device connecting the standard column.

岩棉板是当前建筑行业的产品之一，如今也对岩棉板的要求也越来越高，所以要想使用的更好就要来了解相应问题。更多内容就来网站jyjfsj.com吧。

Rock wool board is one of the products in the current construction industry, and now the requirements for rock wool board are becoming higher and higher. Therefore, if you want to use it better, you need to understand the corresponding problems. For more information, please visit jyjfsj.com Com.